The SEQUENZA 10 implements the line array technology with a perfection and sound quality unknown until now. Intensive fundamental research and development work resulted in a compact line array element with outstanding features. The system’s sound was calibrated with an enormous precision. Two especially developed horn-loaded 10” neodymium chassis and the use of patented FLC® technology guarantee a warm and full sound reproduction as well as excellent full-range qualities. The
dipole arrangement of the chassis and the bass reflex tubes located on the outsides create a high directivity starting at 200 Hz. Using FLC® technology, one of the two 10” drivers is decoupled phase linear so that the coverage area is increasingly reduced. This suppresses gradient side lobes in the coverage pattern and significantly raises the feedback threshold. The tweeter unit of the SEQUENZA 10, which consists of the patented waveformer and three 1” high frequency drivers, creates a planar wavefront up to over 16 kHz. This allows for a coherent coupling of several line array elements even in the frequency range considerably above 10 kHz. With the SEQUENZA 10N’s coverage angle of 77° and the SEQUENZA 10W’s coverage angle of 100°, two
versions are available that can also be combined together in an array using the same controller preset. Despite the compact dimensions, the SEQUENZA 10 is capable of achieving the enormous maximal sound pressure level of 150 dB (peak, with 4x SEQUENZA
10). The patented rigging system ‘Snap&Fly’ saves set-up
time and is unbelievably simple and safe. You preset the angles between the individual speaker elements on the floor. Then, when you fly the array, the individual elements automatically and safely snap into with the correct angles. The compact SEQUENZA 10 B complements the line array system in the low frequency range. The direct radiating 2 x 15" subwoofer can either be flown together with K&F SEQUENZA 10 N/W arrays or used standalone as ground stack or flown as independent bass array. Directional bass arrays can be configured via the K&F SystemRack. The Speakon connectors that are weatherproof according to IP54 and the waterproof enclosure with a Polyurea coating allow for temporary outdoor usages. The SEQUENZA 10 Line Array is intended for use with the K&F SystemRack.
Line Array System with 2 x 10" / 3 x 1" kombined with Waveguide
2 + 1 way passive system
7 x 100 degree
FLC-technologie (patent), Waveguide (patent) and integrated Flyware 'Snap&Fly' (patent)
K&F SystemRack or K&F TOPAS is required for use
Loudspeaker Mount Type - Flown
Loudspeaker Setup - Rigged
Spec Sheet available - Yes
Coverage Horizontal:
100 degrees
Depth:
18.94 in
Height:
11.93 in
Width:
31.30 in
Product Weight:
74.96 lbs
Color:
Black
Design:
2 + 1-way passive system with FLC® technology completely horn loaded, bass reflex tuning
Frequency Response -10 dB(1):
44 Hz - 23,5 kHz in 'FR mode' 58 Hz - 23,5 kHz in 'LCut mode'
Frequency Response -5 dB(1):
49 Hz - 23 kHz in 'FR mode' 87 Hz - 23 kHz in 'LCut mode'
Horizontal Coverage Angle:
100°
Vertical Coverage Angle:
depending on configuration
Nominal power handling LF 1:
300 W RMS, 600 W progam, 1200 W peak
Nominal power handling LF 2 + HF:
300 W RMS, 600 W progam, 1200 W peak
Max. SPL (sinus burst 185 msec @ 10% THD):
134.5 dB RMS, 138 dB peak (1 x SEQUENZA 10) 146.5 dB RMS, 150 dB peak (4 x SEQUENZA 10)
Sinus burst 185 ms with K&F SystemRack:
134 dB RMS, 137.5 dB peak (1 x SEQUENZA 10) 146 dB RMS, 149.5 dB peak (4 x SEQUENZA 10)
Components:
1 x 10" low, 1 x 10" low-mid, both with attached horn, 3 x 1" high frequency driver with 44 mm voice coil
Nominal Impedance:
LF 1: 12 O, Zmin. 12.3 O @ 400 Hz LF 2 + HF: 12 O, Zmin. 10 O @ 220 Hz
Connectors:
2 x Speakon 4 pin NLT4MP
K&F SEQUENZA 10 B
- 15" Flyable Low-Frequency Extension of SEQUENZA 10 Line Array